Custom Rocking Chair Cushions, Made to Your Measurements
Factory-direct, cut to your measurements — rockers, porch rockers, gliders.
Rocking cushions fail where static chair cushions do not: the motion. Every rock drags the seat cushion backward and works the tie roots thousands of cycles a season — two rear-corner ties that would hold for years on a kitchen chair tear out by August on a rocker. That is a sewing problem, not a sitting problem.
We cut rocking chair sets to your numbers — indoor rockers at 17–18 inches, porch wicker rockers at 19–21 — with four box-stitched ties, optional anti-slip undersides, and tie roots reinforced because we know what a rocker does to them. Vintage rockers with tapered seats get front and back widths measured separately.
Build Your Rocking Chair Cushion
Build your rocking chair cushion — start with the shape below.
Enter seat and back dimensions, thickness, and tie positions (slat gaps noted) — then pick your fabric tier.
Open the Customizer — Rectangle Preselected →Need a different shape? Start from all 11 shapes →
Pricing — estimated starting at
| Fabric tier | Estimated price* |
|---|---|
| Cotton Linen | $97 |
| Tech Fabric | $101 |
| Premium Velvet | $106 |
*One rocker set (17 × 17 seat + 17 × 18 back, 2 in.): $39 make-base + 4.1 sq ft × rate ($14.02/$15.13/$16.26 per sq ft, 2" 50D foam + fabric). Seat-only pads cost less.
For comparison: U.S. custom-configurator specialists’ 2026 listings run made-to-order cushions well above formula price once configured — and most only reveal that number after a quote request. We publish the formula above so you can check the math before you order.
Popular Rocking Chair Sizes We Cut
Typical rocking chair sizes by type (typical, always measure):
| Piece | Typical size | Notes |
|---|---|---|
| Indoor wooden rocker (classic) | 17–18 W × 16–17 D seat | Thinner seats (2") keep rocker clearance |
| Spindle / heritage rocker | 17–19 W × 16–18 D | Slatted backs need tie-through gaps |
| Porch wicker rocker | 19–21 W × 18–20 D | Deeper seats than indoor rockers |
| Glider rocker (upholstered) | 19–21 W × 19–21 D | Often thick attached-back pads; brand-specific fits |
| Backs | 17–22 W × 16–25 H | Match seat width; note slat-gap positions |
Yours differs? That’s the point — we cut to your numbers.
How to Measure a Rocking Chair Cushion
- Seat and back seam-to-seam to the nearest quarter inch; vintage rockers with tapered seats get front and back widths measured separately.
- Thread rear ties through the slat gap, not around the rail — that is what prevents the backward walk rocking motion causes.
- Thickness: 2-inch seats keep rocker clearance — the runners need their arc, and thick pads can catch.
- Note slat-gap positions for tie-through backs, and decide tie count before fabric: four outlast two on anything that moves.
Full walkthrough with photos: our measuring guide.
Build details — sewing style and fastening options confirmed with your dimensions before cutting.
Fabric by Where the Rocker Lives
Indoor rockers follow upholstery logic: Cotton Linen for the breathable natural weave, Premium Velvet for formal rooms and claw resistance. Nursery rockers want washable and colorfast above all — Tech Fabric wipes clean of the inevitable spot cleaning. Porch rockers sit between worlds: humidity and indirect UV reach shaded seats, so treat them as semi-outdoor. The tier comparison is in the fabric guide.
Seven of the 119 fabrics in the swatch library — free samples ship with every quote.
Rockers, Gliders, and the Rooms They Live In
- The nursery rocker is the highest-stakes build in the category: hours of nightly use, spot-clean inevitability, and a chair that must not squeak or slide under motion. Washable Tech Fabric, a 2-inch seat to keep the glide arc clear, four reinforced ties, and a back tall enough for a feeding pillow — and the matching ottoman in the same run, because a rocker without its ottoman is half a chair.
- The porch rocker lives in semi-weather: shaded but humid, cool but not dry. Treat it as semi-outdoor — weatherproof fabric, ties threaded through slat gaps rather than around rails, and a build that tolerates the temperature swings a covered porch delivers. The wicker porch rockers of the last forty years run 19–21 inch seats, deeper than their indoor cousins.
- The heritage spindle rocker — the bentwood and slat-back chairs that outlast generations — asks for tie-through backs and a seat pad thin enough (2 inches) to keep the runners their arc. These frames vary more than any catalog admits; vintage rockers with tapered seats get front and back widths measured separately, and the pad is cut to the taper.
- Outdoor rocking chairs are a category of their own and this page builds for them too: open-deck rockers in full weather duty, outdoor fabrics preselected — weatherproof woven over vented foam core, UV-stable thread, and ties that survive both the arc and the storm. The measuring method does not change; the build does.
Frequently asked questions
Can I order standard rocking chair cushion sizes?
Standard sizes too — in 3 clicks: indoor rockers take roughly 17–18 inch seats — stock squares like 17 × 17 and 18 × 18 — and typing the numbers into the customizer gets the same instant factory-direct quote. Tie positions are the part worth measuring on a rocker.
What size cushions fit a standard rocking chair?
Classic indoor rockers take roughly 17–18 inch seat pads and matching backs; porch wicker rockers run 19–21. Measure your seat seam-to-seam to be sure.
How do I keep rocking chair cushions from sliding?
Four ties instead of two, reinforced tie roots, and a non-slip underside — and on wooden rockers, thread rear ties through the slat gap rather than around the rail.
Can I buy replacement cushions for a glider rocker?
Yes — glider cushions are a recognized aftermarket category, but fit is brand-and-model specific (seats 19–21 inches with thick attached-style back pads). Measure your existing set rather than ordering generically.
What’s the best fabric for a nursery rocking chair?
Washable and colorfast — bleach-adjacent spot cleaning is inevitable. Our Tech Fabric wipes clean; Cotton Linen takes gentle washing; Premium Velvet holds up to claws.
Can I use a rocking chair cushion on a glider?
Often dimensionally yes — but the motion differs: a rocker lifts through an arc (ties take rubbing), a glider slides flat (ties take a steady forward pull), and a glider’s cushions must clear the mechanism under the seat. Both want four reinforced ties; the glider build also checks the platform above the hardware. The full glider logic is on our glider cushions page.
How do I stop the back cushion sliding down a rocker?
Ties that land in actual slat gaps — threaded through, not knotted around rails — plus a back cut to the frame’s full height so the frame wedges it in place. A back ordered to the flattened old pad’s numbers comes out shorter than the slot and slides; order to the frame.
Made by the factory that ships them
- Outdoor cushion factory for 10+ years — we cut, fill, and sew every order ourselves.
- Every dimension you send is re-checked before a single yard of fabric is cut.
- Made-to-order means any fabric, any piece, no minimum.
- Cut to ± ½ inch of your confirmed dimensions, in writing — outside tolerance, remade free.
Related categories
- Dining Chair Cushions — static-seat precision for the same rooms
- Glider Cushions — the flat-glide nursery cousin
- Indoor Bench Cushions — long-deck indoor builds
- Outdoor Cushions — the hub for every patio, porch and deck shape
Further reading from the blog
- Rocking chair cushions: the complete guide — sizes, ties and the motion problem — the article behind this page
- Outdoor swing cushions — the same tie mechanics at pendulum scale
- 9 cushion measurement mistakes — and how to avoid the remake
